Probably dry is better so you introduce less moisture and movement into the wall as it dries. In any case you want to keep the coated straw well covered so that it doesn't dry out, or you will need to moisten it again before packing it into the wall.Īs far as the horizontal pins go, I have used both green and dry, both with good results. This supposedly helps the clay soak into the straw so the wall will hold together better, but I have not noticed that it makes a huge difference. And should I use green or dried branch supports inside the walls?Ī: The slip-coated straw can either be packed immediately into the wall cavity, or else left to set up for up to 24 hours. I attended one of 2 of your workshops and have a question as to how long I should let the clay slip straw sit around before tamping into forms. I am building a timber structure and I am going to do Light Straw-Clay infill. feel free to pm or reply to this thread if you need more details or info on tools/materials to get the job done.Q: My question is about Light Straw-Clay. or you can simply cut out a bit more plaster and use the method in the paragraph above. one approach is to simply cut out the large damaged parts into even rectangles, use sheetrock as a base and then come even to the wall with something like easy sand.Ī simple approach to the places where the lath has been cut is to affix some diamond mesh to the existing lath, put down a basecoat of structo-lite on top of the mesh, and then a finish coat with a couple coats of easy sand or similar. The plaster in the picture you show is by no means unsalvagable. Not to mention the horrific mess it makes.Īdding layer after layer of material is, in my opinion, a bad idea and a tremendous amount of effort that could go towards a more appropriate and better looking solution.Įither fix the plaster or take it out and put up sheetrock. You have the same problem if you tear off the lath and plaster and put up sheetrock unless you're replacing windows and doors at the same time, because sheetrock is a lot skinnier than lath and plaster. You'll also have to pull off all the floor trim to make it fit. The problem with putting sheetrock on top of it is you add a lot of weight to the structure of the home (lath and plaster is already crazy heavy) and around windows and doors your life is going to suck. This sucks pretty bad, and obviously you have to take extreme caution with the dust generated. A bit of light sanding and you're done (make sure you wear a mask, and cleanup with a sponge since that paint almost definitely has lead in it).įor big holes, get some 3/4 inch sheetrock (or whatever closest matches the depth of the lath and plaster), and carefully cut out the lath and plaster with a circular saw set to depth. Pack the hole tightly with the styrofoam to provide a base for the plaster of paris, spackle it in, and voila: patched. Try DIY on the Fediverse or Filter by FlairĬonsider patching! This might actually be way easier than affixing sheetrock.įor most holes, get some stiff styrofoam (or stiff expanding foam can work, just be careful not to crack the plaster from behind) and plaster of paris. Please post such content to the appropriate subreddits.Ĭome join us on Discord for real time help and discussion. Promoting your (or anyone else's) social media and commerce channels are not allowed.Ĭrafting, beauty, cooking, cleaning, sewing, etc are not DIY projects. Rude, abusive, toxic or harassing behavior, sexually suggestive or inappropriate comments will be removed and the user permanently banned at the moderator's discretion. Note: - Using /r/DIY as your private search engine is not allowed. This is a basic requirement so others do not spend time repeating your steps. Your question needs include the research you've done to find an answer yourself, or why that research did not answer your question. Check Google and the search bar before turning to /r/DIY. Research first before posting a questions. r/DIY now has a Discord channel! Come chat with us!ĭid you miss the AMA with Patrick DiJusto? Click here to read it!Īll content must be DIY and your own work - if you paid for the work or found it posted online it is not DIY.Īll project submissions must include photos, detailed instructions, photos and/or videos. AMA with Travis Larson is over Check it out!.COVID-19 DIY PPE Post is live, connecting medical professionals with DIYers!.Quinn Dunki of Blondihacks answers your questions! Read her insights into machining and cat dentistry here.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |